SIZES GLOBE/ANGLE Screwed Ends: 1 1/4" - 3" Grooved Ends: 1 1/2" - 6" Flanged Ends: 1 1/4" - 24" (globe); 1 1/4" - 16" ( angle) TEMPERATURE RANGE ( Valve Elastomers) Buna-N -40° F - 180°F Viton 0° F - 400°F SPRING RANGES 50-350 psi MATERIALS Consult factory for others. Body/Bonnet: Ductile Iron (epoxy coated), Carbon Steel (epoxy coated), Stainless Steel, Aluminum Seat Ring: Stainless Steel, Bronze Stem: Stainless Steel, Monel Spring: Stainless Steel Diaphragm: Buna-N, Viton, (Nylon reinforced) Seat Disc: Buna-N, Viton Thermal Relief Pilot: Stainless Steel, Viton Elastomers Other pilot system components: Stainless Steel, Bronze/Brass Tubing & Fittings: Stainless Steel, Copper/Brass SOLENOID Enclosure: Explosion Proof NEMA 4X, 6P, 7, 9 Body: Stainless Steel, Brass Voltages: 24, 120, 240, 480 VAC 12, 24 VDC Note: Working pressures of solenoids vary greatly, consult factory on application of OCV Model 115-26TR valves. Model 115-26TR (Fueling Service) Global performance. Personal touch. TOLL FREE 1.888.628.8258 phone: (918)627.1942 fax: (918)622.8916 7400 East 42nd Place, Tulsa, Oklahoma 74145 email: [email protected] website: www.controlvalves.com SPECIFICATIONS ( Typical Fuel Application) Represented by: For maximum efficiency, the OCV control valve should be mounted in a piping system so that the valve bonnet (cover) is in the top position. Other positions are acceptable but may not allow the valve to function to its fullest and safest potential. In particular, please consult the factory before installing 8" and larger valves, or any valves with a limit switch, in positions other than described. Space should be taken into consideration when mounting valves and their pilot systems. A routine inspection & maintenance program should be established and conducted yearly by a qualified technician. Consult our factory @ 1-888-628-8258 for parts and service. How to order your Model 115-26TR valve When ordering please provide: Fluid to be controlled - Model Number - Size - Globe or Angle - End Connection - Body Material - Trim Material - Elastomer Material - Solenoid Voltage Energize to Open or Close Valve - Special Requirements / Installation Requirements - Thermal Relief Setting REVISED 12/16/10 The solenoid control/check/thermal relief valve shall open and close via discrete electrical signals. The valve shall be equipped with a two-way solenoid valve that will allow the valve to open when <energized, deenergized>. If downstream pressure becomes greater than upstream pressure, the valve shall close to prevent reverse flow; however, should downstream pressure increase to the set point of the thermal relief valve, this valve shall open to relieve the buildup to the upstream side of the valve. The thermal relief valve shall have an adjustable spring range of 50-350 psi. DESIGN The solenoid control/check/thermal relief valve shall be a single-seated, line pressure operated, diaphragm actuated, pilot controlled globe valve. The valve shall seal by means of a corrosionresistant seat and a resilient, rectangular seat disc. These, and other parts, shall be replaceable without removing the valve from the line. The stem of the main valve shall be guided top and bottom by integral bushings. Alignment of the body, bonnet and diaphragm assembly shall be by precision dowel pins. The diaphragm shall not be used as a seating surface, nor shall the pistons be used as an operating means. The pilot system shall be furnished complete and installed on the main valve. It shall include a needle valve, inline strainer and solenoid valve. The solenoid shut-off valve shall be operationally and hydrostatically tested prior to shipment. MATERIALS OF CONSTRUCTION The main valve body and bonnet shall be ductile iron per ASTM A536, Grade 65-45-12. All ferrous surfaces shall be coated with 4 mils of epoxy. The main valve seat ring shall be CF8M stainless steel. Elastomers (diaphragms, resilient seats and O-rings) shall be <Buna-N, Viton>. The needle valve, check valve, thermal relief valve and control line tubing shall be stainless steel. The solenoid shall have a stainless steel body, explosion-proof enclosure and be suitable for operation on <voltage>. OPERATING CONDITIONS The solenoid control/check/thermal relief valve shall be suitable for pressures of <X to X> psi at flow rates up to <X> gpm. ACCEPTABLE PRODUCTS The solenoid control/check/thermal relief valve shall be a <size> Model 115-26TR, <globe pattern, angle pattern>, with <150# flanged, 300# flanged, threaded, grooved> end connections, as manufactured by OCV Control Valves, Tulsa, Oklahoma, USA.
RkJQdWJsaXNoZXIy NDE1MjE4