EATON Aerospace Group TF100-101D May 2013 3 Part 1 - Model number Part 2 - Option letter describing various changes to basic nozzle 64201 Part 3 - Number and/or letter describing male adapter required to mate desired inlet configuration in part 4 and/or ball valve type Part 4 - Letter describing the inlet thread type and size Part 1 Basic model number. Options from Parts 2, 3 and 4 must be added to achieve a complete unit. Part 2 The following options may be added as Part 2 of the part number, as illustrated above, to order a unit to meet your requirements: The part number of a complete nozzle consists of four basic parts as shown at right (cont’d on page 4): Ordering Data Option Description Option Description *A Adds 40-mesh screen K 2-inch female camlock quick disconnect (QD) *B Adds 60-mesh screen L Adds extended circular handle assy *C Adds 100-mesh screen M Adds circular handle assy D Adds bonding cable N Adds D-3 inlet coupling E Adds vacuum breaker P Adds elbow Inlet (modified for flanged type regulator **F3 Adds 35 psi (2.413 bar) hose end regulator Q GTP-235-3/8 — Gammon jet test QD **F4 Adds 45 psi (3.103 bar) hose end regulator R Adds interlock mounting bracket **F5 Adds 55 psi (3.792 bar) hose end regulator S Adds holder bracket (not needed with option U) G Adds bonding cable U Replaces stick handles with stirrup handle and integral interlock bracket H Adds elbow inlet (D-1) V Adds bonding cable J Adds straight inlet (D-2) W Inlet per MIL-C-24356 * Options A, B, and C only available when a male half or a ball valve from Part 3 is specified ** To obtain a nozzle with two regulators, specify two options in series, F5F4 results in 55 psi (3.792 bar) and 45 psi (3.103 bar) units with the 55 psi (3.792 bar) unit assembled as the one nearest the inlet. If two regulators with different pressures are required, the higher pressure unit should be specified first. Part 3 The configuration of the inlet is defined by adding the appropriate number or number and option letter from the table (right) in conjunction with the appropriate option letter from Part 3. The nozzle may terminate in an adapter half only, if desired. In this case leave Part 4 blank. To obtain a female half, quick disconnect (QD) or dry break, or to complete the specification of the ball valve outlet, Part 4 must be completed. Option Description Option Description 1 Specifies hose end regulator with flanged end (with Option F, part 2) 5 Adds 2-inch unisex coupling, valved 2 Military male adapter to mate QD 6** Adds male adapter, dry break *3 Adds ball valve (64015). May be ordered with Options D, E, J and R, below 6Y Adds male adapter, low pressure drop drybreak D Adds glass inspection port to ball valve 7** Adds dry break male adapter with Option F E Adds drag ring to ball valve 8** Adds dry break male adapter without Option F J Adds handle spanner to ball valve 9 Adds male adapter to mate 60427 style QD R Adds 1/8-inch hex key to ball valve X Adds 2-inch unisex coupling — non-valved 4 Adds flight refueling male QD adapter Z Adds 2-inch unisex coupling — non-valved, non-swivel * The inlet size and configuration option from Part 4 must be included in the part number with Option 3 to achieve a complete nozzle and ball valve ** Safety clip (P/N 210641) for the 61154 dry break QD is considered Foreign Object Debris (FOD) and not included on military nozzle assemblies, however, it can be added as a no cost option
RkJQdWJsaXNoZXIy NDE1MjE4