EATONAerospace Group TF100-105D May 2013 3 The part number for a complete nozzle consists of four parts as illustrated (right). Ordering Data Part 2 The following options may be added to part two of the part number to obtain the desired unit configuration. 64250 Part 1 - Model number Part 2 - Option letter describing various changes to basic nozzle Part 3 - Number and/or letter describing male adapter required to mate desired inlet configuration in Part 4 and/or ball valve type Part 4 - Letter describing the inlet thread type and size Option Description Option Description *A Adds 40-mesh screen K Replaces standard operating handle with longer one *B Adds 60-mesh screen L Replaces standard carrying handles with circular handle C Adds 100-mesh screen P Adds pressure gauge with protective bracket D Adds bonding cable Q Adds Gammon sampling quick disconnect E Adds vacuum breaker R Adds nozzle stowage bracket **F3 Adds 35 psi (2.413 bar) HECV S Adds 45° nozzle stowage bracket **F4 Adds 45 psi (3.103 bar) HECV T Adds adapter to mate Whittaker accessories **F5 Adds 55 psi (3.792 bar) HECV U Replaces standard handle with stirrup handles G Replaces standard handles with long handles (47233-2) V Replaces standard carrying handles with UK RAF style handles H Adds drag ring to nozzle with any Option F in conjunction with Option T or Options 2 or 6 from Part 3 (220870) W Adds military style bonding cable J Inlet adapter to mate 60427 style outlet Y Adds swivel elbow * Options A, B & C only available when a male half from Part 3 is specified ** To obtain a nozzle with a dual HECV setup specify two options in series, F5F4 results in 55 psi (3.792 bar) and 45 psi (3.103 bar) units with the former assembled nearest the nozzle inlet. If two HECV’s are desired specify the highest pressure setting first. Part 3 The configuration of the inlet is defined by adding the appropriate number(s) and/or letter(s) from the table below as Part 3 in conjunction with the appropriate option letter from Part 4. Option Description Option Description *1 Indicates nozzle with flanged inlet HECV R Adds defuel key to remove strainer cap to ball valve *2 Indicates nozzle with swivel inlet HECV 4 Adds male adapter half (44701 without HECV, 44185 with flanged inlet HECV, 44697 with swivel inlet HECV) to mate basic nozzle and thumb latch QD 3 Adds ball valve (64015). Options D, E, J & R (below) may be added to complete the ball valve specification 6 Adds male adapter half to mate standard QD D Adds glass inspection port to ball valve 7 Adds male adapter half (44697 without HECV, 44185 with flanged inlet HECV) to mate dry break QD E Adds drag ring to ball valve 9 Adds male adapter half (43046 with flanged inlet HECV, 44362 otherwise) to mate 60427 style QD J Adds spanner wrench to ball valve * If Option 1 or 2 is used with no additional options from Part 3, then the shortest configuration nozzle will be provided Part 4 The following options may be added to obtain a female half, QD or dry break, or to complete the specification of the ball valve outlet. The nozzle may terminate in an adapter half only. In this case leave Part 4 blank. Option Description Option Description H Inlet thread — 2½-inch NPT N Inlet thread — 2-inch BSPP K Inlet thread — 2½-inch BSPP P Inlet thread — 2-inch NPT L Inlet thread — 3-inch NPT Z Inlet thread — 3-inch JIS (used only with Options 6 and 9) * M Inlet thread — 3-inch BSPP * Three-inch BSPP inlet threads not available with Option 3 Ball Valves Examples: 64250CD6H Nozzle with 100-mesh screen, bonding cable and standard QD with 2½-inch NPT inlet thread 64250BF41 Nozzle with 60-mesh screen, 45 psi (3.103 bar) HECV with inlet flange to mate 60427 type accessories. Note that no inlet QD or other configuration is specified in this case. 64250F517P Nozzle with 55 psi (3.792 bar) HECV with flanged adapter half and 61154 dry break QD with 2-inch NPT inlet. Note: swivel adapter half and 61154 dry break QD can be specified by using 64250F527P.
RkJQdWJsaXNoZXIy NDE1MjE4