EATON Aerospace Group TF100-107E May 2013 5 The part number for a complete nozzle consists of five parts as illustrated (right). 64349 Part 1 - Model number Part 2 - Option letters describing various changes to basic nozzle * Part 3 - Number and/or letter describing the various adapters, ball valves & other accessories as noted below * Part 4 - Letter describing the inlet thread type and size * Parts 3 and 4 not applicable for D-1, D-2 or D-3 configurations Option Description Option Description *A Adds 40-mesh screen H Adds 45° elbow — D-1 Style *B Adds 60-mesh screen J Adds straight inlet — D-2 Style *C Adds 100-mesh screen K Adds QD with 2-inch female camlock inlet D Adds bonding cable N Adds D-3 inlet coupling E Adds vacuum breaker Q Adds Gammon sampling QD F1 Adds 15 psi (1.034 bar) hose end regulator R Adds circular handle grip F3 Adds 35 psi (2.413 bar) hose end regulator W Adds straight inlet per MIL-C-24356 F4 Adds 45 psi (3.103 bar) hose end regulator **X Adds safety clip for dry break QD F5 Adds 55 psi (3.792 bar) hose end regulator Y Adds extended grounding cable F6 Adds 48 psi (3.309 bar) hose end regulator Z Arctic weather nozzle * Options A, B, and C only available with Options V or X or when a male half or a ball valve from Part 3 is specified ** Safety clip (p/n 210641) for the 61154 Dry Break QD is considered FOD (Foreign Object Debris) and not included on military nozzle assemblies; however, it can be added as a no cost option. Part 2 The following options may be added as Part 2 of the part number as indicated above to order a unit to meet your requirements. Option Description Option Description 2 Adds military male adapter, disconnect 5 Adds 2-inch unisex coupling, valved *3 Adds Hose End Ball Valve (HEBV) 6 Adds military male adapter, dry break 3D HEBV with glass inspection cap 7 Adds dry break male adapter with Option F 3E HEBV with drag ring 8 Adds dry break male adapter without Option F 3DE HEBV with glass inspection cap and drag ring **9 Adds male adapter half to mate 60427 style QD 31 HEBV with male QD assy M Adds 3-inch unisex coupling, valved 31D HEBV with male QD assy and inspection cap V Adds 2-inch unisex coupling, non-valved, green 31E HEBV with male QD assy and drag ring X Adds unisex coupling, non-valved, tan 31DE HEBV with male QD assy, inspection cap and drag ring * The inlet size and configuration option from Part 4 must be included in the part number with Option 3 to achieve a completed nozzle and ball valve ** Not used with Options H, J or N from Part 1 Part 3 The configuration of the outlet is defined by adding the appropriate number or number and option letter from the table (right) in conjunction with the appropriate option letter from Part 4 below. The nozzle may terminate in an adapter half only, if desired. In this case leave Part 4 blank. To obtain a female half QD or dry break, or to complete the specification of the ball valve outlet, Part 4 must be completed. Option Description Option Description H Inlet thread — 2½-inch NPT S 2-inch camlock Inlet *L Inlet thread — 3-inch NPT T 2-inch female camlock with locking handle to D1 flange with camlock dust cap P Inlet thread — 2-inch NPT * 3 inch inlet threads not available with Option 3 HEBV Some of the above option letters may be duplicates of those found in Part 2. They must be accompanied by a number from Part 3 to be effective. Part 4 One of the following letters must be included as Part 4 to specify the inlet thread size. Ordering Data Part 5 The following letters may be included as Part 5 to add handle options to the HEBV (Option 3 from Part 3). Option Description Option Description J Adds spanner handle S Adds short handle R Adds hex key * Part 5 - Letter describing ball valve handle options
RkJQdWJsaXNoZXIy NDE1MjE4