CANADA’S LEADER IN ENERGY PRODUCTS EQUIPMENT PUMPS, COMPRESSORS & MOTORS CORKEN CORO-FLO & CORO-VANE PUMPS Coro-Vane Positive Displacement Plant Pumps Coro-Vane® pumps are typically used for cylinder filling docks and bulk truck loading / unloading. Various mounting options include V-belt or direct drive with a gear reducer. Depending on the model, maximum pump speeds can run up to 950 rpm. These pumps feature sliding vane technology for long life and consistent performance, replaceable liners, reversible side plates and a design that allows for easy seal replacement through one side of the pump. NEE # NEE #(with base) Max HP Rating Max PSID Capacity based on RPM Inlet Size Outlet Size Shaft Size Z2000HGAEEU NLA 15 125 25-90 GPM 2” 2” 1 1/8” 521EGAJE 521EGAJE-103-9 2-1/2” 1021EGAMM 1021EGAMM-103-10-215 20 40-200 GPM 3” 3” Z3500HGAMT Z3500-103-10-254T 15 150 125-435 GPM 3” NPT (standard) 3” NPT (elongated) Z4500HGASP Z4500EGASP-103-15 25 4” ANSI Flange 3” ANSI Flange 1 1/4” Note: Capacities are based on 70º temperature, no pressure loss on pump suction and vapour equalized pumping conditions. Coro-Vane Truck Pumps Z-Series The Z-Series Coro-Vane® Truck Pumps are specifically designed to perform in such severe operating conditions as high differential pressure, pump over speeding, poor suction and heavy thrust loads associated with a power take-off (PTO) drive system. Advantages Include: Innovative cam design virtually eliminates cavitation. New materials utilized in cam and blades extend pump life. Large diameter, non-metallic pins are suitable for higher pump speeds. Locked rotor is factory set w/shim adjusted thrust bearings (rated @ 4,000+ lbs.) NEE # Working Pressure Max RPM Max PSID Capacity GPM at 50 PSID Capacity GPM at 100 PSID Inlet Size Outlet Size NEE # for Hydraulic Adapter Z3200HGAPGE 400 800 125 121 110 3” ANSI Flange 2” NPT COR 4496-x1 Z4200HGASEE 400 360 4” ANSI Flange COR 4496-1x1 CORKEN COMPRESSORS Compressors NEE # RPM Max. Liquid Transfer GPM (LPM) Piston Displacement CFM (CU Mtrs/Hr) Max Driver Size (HP) Pipe Diameter Vapour Pipe Diameter Liquid 291AM3FBANSNN 825 88 (333) 16 (27.2) 15 3/4” 3/4” 491AM3FBANSNN 198 (749) 36 (16.2) 1 1/4” 1 1/4” 691AM3FBANSNN 330 (1249) 60 (102) 30 2” 1 1/2” 91AJ3FBANSNN 44 (166) 8 (13.6) 7 1/2 3/4” 3/4” Note: Capacities are a guideline only. Consult NEE and the manufacturer’s documentation for specifications. Z2000HGAEEU Z3200HGAPGE Z4200HGASEE Liquefied gas transfer on a large scale is more economically achieved with the use of a compressor than with a pump. Compressors are used to increase vapour pressure in the tank you wish to empty and push the liquid into a secondary tank that is the source of the product used to provide the vapour pressure. Once all the liquid is transferred, the 4 way valve allows you to switch to the vapour recovery mode and remove the residual liquid (liquid heel) and then pull the vapour pressure down to a level unachievable with a pump. Corken is a world-wide leader in LP gas compressors and can also provide compressors for most industrial gas transfer applications. Available in various optional configurations, with distance pieces, liquid traps, switches, valves, etc. Contact NEE for detailed specifications 107 Configuration 491 Configuration
RkJQdWJsaXNoZXIy NDE1MjE4