Retail Petroleum Equipment

BENEFITS ■ PetroClear models 40910W and 40930W are particulate removing and water sensing spin-on filters designed for cost efficient particulate filtration of fuels at high volume fueling locations such as truck stops, card lock sites, and industrial/ commercial applications. ■ The 40910W and 40930W are designed to remove particulate and to sense both free and emulsified water from NEAT GASOLINE, diesel, Biodiesel, ULSD (Ultra Low Sulfur Diesel), Kerosene, and fuel oils. This filter will not sense nor react to water in Ethanol-blended gasoline. (Reaction known as phase separation) ■ PetroClear models 40910W and 40930W are particulate and water sensing spin-on filters. These filters are designed to sense water, both free and emulsified, and slow flow as an indicator of the presence of water in NEAT GASOLINE and diesel fuels. ■ PetroClear model 40910W filter offers efficient 10 micron nominal particulate removal (nominal = 75% efficiency) and senses both free and emulsified water in NEAT GASOLINE. ■ PetroClear model 40930W filter offers efficient 30 micron nominal particulate removal (nominal = 75% efficiency) and senses both free and emulsified water in NEAT GASOLINE. ■ UL recognized for NEAT GASOLINE and diesel fuels. ■ Will not detect phase separation in Ethanol blended fuels. ■ Compatible with Biodiesel. ■ The water-sensing filter is not a fool-proof mechanical positive shut-off. If this filter remains in service after going into slow flow it can return to full flow, allowing contaminated fuel to be dispensed into the consumer’s vehicle and cause potential damage. 409 SERIES WATER SENSING & PARTICULATE REMOVING 40910 W and 40930W Extended LifeWater Sensing SPECIFICATIONS ■ The PetroClear model 40910W utilizes a 10 micron cellulose media to remove particulate from gasoline and diesel fuels including Biodiesel and ULSD (Ultra Low Sulfur Diesel). Removes a minimum of 75% of particulate 10 micron in size (and approximately 100% of larger particulate) with water sensing capability in NEAT GASOLINE and diesel fuels. ■ The PetroClear model 40930W utilizes a 30 micron cellulose media to remove particulate from gasoline and diesel fuels including Biodiesel and ULSD (Ultra Low Sulfur Diesel). Removes a minimum of 75% of particulate 30 micron in size (and approximately 100% of larger particulate) with water sensing capability in NEAT GASOLINE and diesel fuels. ■ Once PetroClear models 40910W and 40930W have absorbed 10.7 ounces (315 mil) of water from NEAT GASOLINE or diesel fuel, flow will be noticeably slow. ■ The maximum flow rate for PetroClear models 40910W and 40930W is 20 gpm (76 lpm). Maximum operating pressure is 50 psid (3.4 bar). Maximum differential pressure is 25 psid (1.7 bar). Collapse pressure is 150 psid (10.3 bar). Maximum operating temperature is 250°F (139°C). ■ PetroClear models 40910W and 40930W utilize a standard 1"–12 UNF mounting thread ref. (3/4" flow) required for most spin-on filter adaptors used in aftermarket. ■ PetroClear models 40910W and 40930W utilize an epoxy coated interior shell to eliminate oxidation (rusting), which can cause pinhole leaks from the inside of the filter shell. ■ Adaptors are available for models 40910W and 40930W in aluminum and cast iron.These single adaptors are available in both 3/4" and 1" NPT or BSP inlet/outlet threads. For disposal information please contact your nearest EPA office. 02-10 PC-409-W+P NOTE: If you experience frequent filter changes, it is recommended that you have fuel samples analyzed to determine the source of contamination, such as water, dirt, rust, bacteria, phase separation, etc. PetroClear FILTERS ARE NOT TO BE USED INAVIATION FUEL APPLICATIONS.