Retail Petroleum Equipment

45 SUBMERSIBLE PUMPING SYSTEMS SUBMERSIBLE PUMPING SYSTEMS A typical turbine model designation has up to five components to define the pump being supplied as follows: STP XXXXX Y - A - B STP = Basic Model Designation XXXXX = Factory Installed Options STP model designations may include one or more of the following characters in alphabetical order: AG = Alcohol-gasoline compatible (up to E85, up to B20, and B100) Note: Standard models up to 10% ethanol capable. F = Floating suction adapter (1½" NPT female adapter) H = High pressure (1½ hp and 2 hp models only) K = Intake filter screen (IFS, factory installed to PMA) M = MagShell ® (2 hp models only) *R = Model R check valve (24 psi relief / 22 psi reset for PLLD) *W = Model W check valve (16 psi relief/13 psi reset for PPM4000) Model Description Model Length * Range STP33 1/3 hp fixed speed 37" - 132" STP75 ¾ hp fixed speed 37" - 132" STP150 1½ hp fixed speed 37" - 132" STPH150 1½ hp high pressure fixed speed 37" - 132" STPM200 2 hp fixed speed with MagShell ® 37" - 132" STPHM200 2 hp high pressure fixed speed with MagShell ® 37" - 132" Notes: 1. Remove “M” from model number for non-MagShell ® pump motor assembly. 2. STP models are compatible with fuel mixtures containing up to 10% ethanol with gasoline, up to 5% Biodiesel with diesel fuels, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. STPAG models are compatible with fuel mixtures containing diesel fuel with up to 20% Biodiesel, 100% Biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. 3. All models are supplied with a standard check valve unless factory option “R” or “W” is specified. 4. All above models require single-phase, 208-230 VAC, 60 Hz incoming power. 5. 4" riser pipe, if supplied locally, must be 4½" OD by 3/16" WT tubing. 6. For riser pipe lengths 31" to 60", additional charges apply (call Customer Service for lead times). *Model length (A) defined as the dimension from turbine manifold bottom to pump motor inlet. Model length (A) can be a minimum of 37" to a maximum of 211". Adder (p/n 400326912) applies if model length is 133" to 180" (charge is for boards to protect STP shipment). Adder (p/n 400326917) applies if model length is 181" to 211" and (p/n 400389112) applies if model length is 212" to 246" (additional charge is for crating to protect the STP). Veeder-Root ® is a trademark of Danaher Corporation. Red Jacket™ is a trademark of Veeder-Root Company. SUBMERSIBLE TURBINE PUMPS Y = Pump Motor Horsepower Rating 33 = 1/3 hp fixed speed 75 = ¾ hp fixed speed 150 = 1½ hp fixed speed 200 = 2 hp fixed speed A = Model Length Model length is expressed as three numeric characters that indicate the length of the STP from the turbine manifold bottom to the pump motor inlet in inches, available from 37" to 211" (additional charge for models 133" and longer). B = Riser Pipe Length Riser pipe length is expressed as two numeric characters that indicate the total length of the riser in inches. Riser pipes are available from 7" to 60" in 1" increments (additional charge for risers 31" or longer). *Note: If not otherwise specified, all STP models supplied with standard model check valve (40 psi relief / 35 psi reset for MLD, TS-LS300, and TS-LS500). Fixed Length SubmersibleTurbine Pump Model Designation System Fixed Length SubmersibleTurbine Pumpa