Retail Petroleum Equipment

31 SUBMERSIBLE PUMPING SYSTEMS SUBMERSIBLE PUMPING SYSTEMS SPECIFICATIONS Power Requirements • 2 hp fixed speed models require single-phase, 208-230 VAC, 60 Hz incoming power. • 2 hp fixed speed models incorporate a starting and running capacitor, with internal bleed resistor, rated 370 Volt, 40 microfarad. • STP-SCI single-phase Smart Controllers and STP-CBS single-phase control boxes are available for 2 hp pump control. • Max. motor draw: 12 Amps. Pump Motor • 2 hp fixed speed, 3450 rpm, multi-stage centrifugal type pump motor with integral, automatic, thermal overload protection. • Standard pressure (M200, two-stage) model, max. pressure = 36 psi. • High pressure (HM200, three-stage) model, max. pressure = 45 psi. • Available with MagShell ® for 45% increased flow area around motor. Liquid Compatibility • 2 hp fixed speed models are available in variable length and fixed length options. • Check valve: 2¾" diameter fluorocarbon seal constructed with cast aluminum body and steel backing washer. • Pressure relief valve: available in four pressure relief settings, integral to check valve. Standard model relieves at 40 psi and resets above 35 psi. • Syphon: venturi-type syphon primer supplied with every submersible. Syphon check valve and secondary syphon sold separately. • Air eliminator: every submersible includes a tank return path with one-way check valve to provide active air elimination. • Electrical disconnect: electrical yoke for positive contractor disconnect during service. Approvals/Certifications • cULus listed. • Consult factory for applicable approvals. Quality Certification • Franklin Fueling Systems is an ISO 9001 Certified Manufacturer • Max. liquid viscosity: 70 SSU at 60 °F (15 °C). • Standard STP models are UL and cUL listed for fuel mixtures containing up to 10% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. • STPAG (AG compatible) models are UL and cUL listed for fuel mixtures containing diesel fuel with up to 20% Biodiesel, 100% Biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. • 2 hp fixed speed models can also be used with diesel fuels, fuel oils, kerosene, Avgas and jet fuels in a non- gelled pourable state. • All wetted elastomers are made of a high grade, fluorocarbon compound. 2 hp Fixed SpeedTurbine Performance Chart 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 0 20 40 60 80 100 120 140 160 180 200 220 Flow in Gallons per Minute (gpm) Total Head in Feet (ft.) Note: Performance based on pumping solvent (0.78 specific gravity). Pressure is taken at the manifold discharge outlet. STPM200 models are powered by a single-phase, 60 Hz, 208/230Volt power supply. One STPM200 2 hp MagShell ™ Fixed Speed Pump Two STPM200, Manifolded 2 hp MagShell ™ Fixed Speed Pumps 2 hp High Pressure Fixed SpeedTurbine Performance Chart 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 0 20 40 60 80 100 120 140 160 180 200 220 Flow in Gallons per Minute (gpm) Total Head in Feet (ft.) Note: Performance based on pumping solvent (0.78 specific gravity). Pressure is taken at the manifold discharge outlet. STPHM200 models are powered by a single-phase, 60 Hz, 208/230Volt power supply. One STPHM200 2 hp High Pressure MagShell ™ Pump Two STPHM200 Manifolded 2 hp High Pressure MagShell ™ Pumps Performance SUBMERSIBLE TURBINE PUMPS