Retail Petroleum Equipment

35 SUBMERSIBLE PUMPING SYSTEMS SUBMERSIBLE PUMPING SYSTEMS SPECIFICATIONS Power Requirements • 1½ hp fixed speed models require single-phase, 208-230 VAC, 60 Hz incoming power. • 1½ hp fixed speed models incorporate a starting and running capacitor, with internal bleed resistor, rated 370 Volt, 15 microfarad. • STP-SCI single-phase Smart Controllers and STP-CBS single-phase control boxes are available for 1½ hp pump control. • Max. motor draw: 11 Amps. Pump Motor • 1½ hp fixed speed, 3450 rpm, multi-stage centrifugal type pump motor with integral, automatic, thermal overload protection. • Standard pressure (150, two-stage) model, max. pressure = 34 psi. • High pressure (H150, three-stage) model, max. pressure = 46 psi. Liquid Compatibility • 1½ hp fixed speed models are available in variable length and fixed length options. • Check valve: 2¾" diameter fluorocarbon seal constructed with cast aluminum body and steel backing washer. • Pressure relief valve: available in four pressure relief settings, integral to check valve. Standard model relieves at 40 psi and resets above 35 psi. • Syphon: venturi-type syphon primer supplied with every submersible. Syphon check valve and secondary syphon sold separately. • Air eliminator: every submersible includes a tank return path with one-way check valve to provide active air elimination. • Electrical disconnect: electrical yoke for positive contractor disconnect during service. Approvals • cULus listed. • Consult factory for applicable approvals. Quality Certification • Franklin Fueling Systems is an ISO 9001 Certified Manufacturer. • Max. liquid viscosity: 70 SSU at 60 °F (15 °C). • Standard STP models are UL and cUL listed for fuel mixtures containing up to 10% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. • STPAG (AG compatible) models are UL and cUL listed for fuel mixtures containing diesel fuel with up to 20% Biodiesel, 100% Biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. • 1½ hp fixed speed models can also be used with diesel fuels, fuel oils, kerosene, Avgas, and jet fuels in a non- gelled pourable state. • All wetted elastomers are made of a high grade, fluorocarbon compound. Performance 1½ hp Fixed SpeedTurbine Performance Chart 0 10 20 30 40 50 60 70 80 90 100 110 0 20 40 60 80 100 120 140 160 180 200 Flow in Gallons per Minute (gpm) Total Head in Feet (ft.) Note: Performance based on pumping solvent (0.78 specific gravity). Pressure is taken at the manifold discharge outlet. STP150 models are powered by a single-phase, 60 Hz, 208/230Volt power supply. Two STP150 Manifolded 1½ hp Pumps One STP150 1½ hp Pump 1½ hp High Pressure Fixed SpeedTurbine Performance Chart 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 0 20 40 60 80 100 120 140 Flow in Gallons per Minute (gpm) Total Head in Feet (ft.) Note: Performance based on pumping solvent (0.78 specific gravity). Pressure is taken at the manifold discharg outlet. STPH150 models are powered by a single-phase, 60 Hz, 208/230Volt power supply. One STPH150 1½ hp High Pressure Pump Two STPH150 Manifolded 1½ hp High Pressure Pumps SUBMERSIBLE TURBINE PUMPS