Retail Petroleum Equipment

26 SPECIFICATIONS Power Requirements • Variable speed pumps can only be controlled by a MagVFC™ variable frequency controller: • VS2 models can operate with single- or three-phase incoming power supply to the MagVFC™. • VS4 models require three-phase incoming power supply to the MagVFC™ for proper operation. • Incoming power supply to the MagVFC™ can be 200-250 VAC, 50 or 60 Hz. • MagVFC™ outputs a three-phase, variable frequency signal, valid for FE PETRO ® variable speed pumps only. • MagVFC™ max. line draw: 20 Amps. Pump Motor • 2 hp or 4 hp, variable speed, two-stage centrifugal type pump motor with integral, automatic, thermal overload protection. • Max. pressure: selectable operating pressure on MagVFC™ between 24 psi and 42 psi deadhead. • Available with MagShell ® which results in 45% increased flow area around motor. Liquid Compatibility • Max. liquid viscosity: 70 SSU at 60 °F (15 °C). • STP variable speed models are UL and cUL listed for fuel mixtures containing up to 10% ethanol, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. • IST variable speed models are UL and cUL listed for fuel mixtures containing diesel fuel with up to 20% Biodiesel, 100% Biodiesel, up to 85% ethanol with gasoline, and 20% MTBE, 20% ETBE or 17% TAME with gasoline. • All variable speed (non-AG) models can also be used with diesel fuels, fuel oils, kerosene, Avgas and jet fuels in a non-gelled pourable state. • All wetted elastomers are made of a high grade, fluorocarbon compound. • Variable speed models are available in variable lengths only. • Check valve: 2¾" diameter fluorocarbon seal constructed with cast aluminum body and steel backing washer. • Pressure relief valve: available in four pressure relief settings, integral to check valve. Standard model relieves at 40 psi and resets above 35 psi. • Syphon: venturi-type syphon primer supplied with every submersible. Syphon check valve and secondary syphon sold separately. • Air eliminator: every submersible includes a tank return path with one-way check valve to provide active air elimination. • Electrical disconnect: electrical yoke for positive contractor disconnect during service. 2 hp Variable Speed Turbine Performance Chart 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 0 20 40 60 80 100 120 140 160 180 200 220 Total Head in Feet (ft.) One MVS2, 2 hp MagShell ™ Variable Speed Pump Two MVS2, Manifolded 2 hp MagShell ™ Variable Speed Pumps Flow in Gallons per Minute (gpm) 4 hp Variable Speed Turbine Performance Chart 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 Total Head in Feet (ft.) Two MVS4, Manifolded 4 hp MagShell ™ Variable Speed Pumps One MVS4 4 hp MagShell ™ Variable Speed Pump Flow in Gallons per Minute (gpm) Approvals • cULus listed. • Consult factory for applicable approvals. Quality Certification • Franklin Fueling Systems is an ISO 9001 Certified Manufacturer. Note: Performance based on pumping gasoline (0.76 specific gravity). Pressure is taken at the manifold discharge outlet. ISTM and STPMVS2 turbines can only be powered by a MagVFC with single or three phase incoming power. Note: Performance based on pumping gasoline (0.76 specific gravity). Pressure is taken at the manifold discharge outlet. ISTMVS4 and STPMVS4 turbines can only be powered by a MagVFC with three phase incoming power SUBMERSIBLE TURBINE PUMPS