Retail Petroleum Equipment

339 FUEL MANAGEMENT SYSTEMS FUEL MANAGEMENT SYSTEMS Model Description TS-PRB 12 input probe module, LL2 and LL3 Series mag probes, VFM flow meters and DMS Mag sensors, and all -U sensors TS-2WSNS 12 input 2-wire sensor module, FMP-ULS, FMP-UHS, TSP-HLS, TSP-ULS, TSP-UHS, TSP-HLSXL, and FMP-HFS sensors TS-3WSNS 8 input 3-wire sensor module, FMP-EIS, FMP-DIS, FMP-DDS, FMP-DTS, FMP-HIS, FMP-ULS, FMP-UHS, TSP-MWS, FMP-HFS, TSP-ULS, TSP-UHS, TSP-HLS, TSP-HLSXL and TSP-DVS sensors. Can also support 2-wire sensors (FMP-EIS-U, FMP-DIS-U, FMP-DDS-U, FMP-DTS-U, FMP-HIS-U) TS-420IB 8 input 4-20 mA module, LSU500 transducers and VPS and SCCM pressure sensors Model Description TS-ACI 12 input AC input module, dispenser hook inputs TS-RLY 8 output relay module, SCCM solenoid and STP control TS-10ARLY 6 output 10 Amp relay output module, dispenser power TS-IO Input output module, 4 output 4-20 mA, 8 input 3-240 VAC/DC TS-420EXP 8 input 4-20 mA module, LSU500E transducers and external devices Note: TS-RLY Module is not required for STP control when utilizing turbine pump interface (TPI) communications. Do not include Power Supply and Controller Module when calculating total modules allowed. Note: Using turbine pump interface (TPI) communications eliminates the need for a TS-RLY module; FFS intelligent controllers required. Note: Using turbine pump interface (TPI) communications eliminates the need for a TS-RLY module; FFS intelligent controllers required. Model Description TSP-WDCBL Wayne™ cable TSP-TDCBL Tokheim™ cable TSP-GDCBL Gilbarco ® cable TSP-GSDCBL Gilbarco ® G-Site™ cable TSP-BDCBL Bennett ® 515 only cable Model Description TS-LS500/1 1-line transducer kit TS-LS500/2 2-line transducer kit TS-LS500/3 3-line transducer kit TS-LS500/4 4-line transducer kit For new installations where separate low voltage conduits can be used. Use TS-420IB module. Note: For new installations where separate low voltage conduits can be used. Use TS-420IB module. Bennett ® is a registered trademark of Bennett Pump Company. Wayne™ is a trademark of Dresser Equipment Group Inc. Gasboy ® , Gilbarco ® , Encore™, and G-Site™are trademarks of Gilbarco Inc. Tokheim™ is a trademark of Tokheim Holding B.V. For retrofit installations where only a high voltage conduit can be used. Use TS-420EXP module. Model Description TS-LS500E/2 2-line transducer kit, explosion proof TS-LS500E/3 3-line transducer kit, explosion proof TS-LS500E/4 4-line transducer kit, explosion proof Model Description TS-AFALNIP Leak generator needle valve kit required for E85 installations EVO™ 550 & EVO™ 5000 ACCESSORIES The EVO TM 550 and EVO TM 5000 Automatic Tank Gauges come standard with a power supply module and a controller module. Additional interface modules can be installed. Interface modules ordered with an ATG will be installed at the factory. The following guidelines must be followed: • EVO TM 550: Six total modules can be installed with a maximum of four intrinsically safe modules and a maximum of three of any one kind of module. • EVO TM 5000: Eleven total modules can be installed with a maximum of nine intrinsically safe modules and a maximum of three of any one kind of module. Pressurized line leak detection provides automatic 3.0 gph hourly, 0.2 gph monthly and 0.1 gph annual precision line leak detection for the EVO TM 550 and EVO TM 5000 ATGs. Statistical Line Leak Detection (SLLD) is a standard feature that can provide 0.2 gph monthly results on even high throughput lines. Available in intrinsically safe and explosion proof models. Use explosion proof when low voltage conduit is not available. The TS-420IB or TS-420EXP, TS-ACI and TS-RLY module and TS- ELLD software option must be ordered and installed in the fuel management system ATG. EVO TM 550 and EVO TM 5000 AutomaticTank Gauges Interface Modules TS-LS500 AutoLearn™ with Statistical Line Leak Detection FUEL MANAGEMENT SYSTEM CONSOLES Intrinsically Safe Modules Non-Intrinsically Safe Modules Intrinsically Safe Explosion Proof Dispenser Interface Module Cables Alternative Fuels Accessories